Aller au contenu

Rivets pour bateau


Bach

Publications recommandés

Perso j’aurais été avec des boulons de stainless, l’alu je doute de leur resistance. Par contre avec des boulons ca te prend un acces l’autre côté au même titre que les rivets ‘’puncher’’ comme les avions.

Lien vers le commentaire
Partager sur d’autres sites

il y a 17 minutes, tom123 a dit :

Perso j’aurais été avec des boulons de stainless, l’alu je doute de leur resistance. Par contre avec des boulons ca te prend un acces l’autre côté au même titre que les rivets ‘’puncher’’ comme les avions.

Stainless sur aluminium tu vas finir par avoir de la corosion galvanique. En plus que c'est sous l'eau... Bonjour les trous dans X années!

 

@Bach c'est toi qui vois, tu as quand même un vidéo youtube qui montre que ça marche pareil.

Si tu te mets une ligne tout le tour des pods et des trous de 3M 5200 (c'est une colle polyuréthane, comme de la PL Premium), je ne vois pas comment boulonner serait mieux. Bien que la PL Premium ne soit pas côté immersion, plusieurs raportent du succès sous la ligne d'eau. De toute façon tu batis pas un bateau (comme moi!) donc je te conseille direct la 3M 5200, pour 10-15$ de différence dans ton projet...

 

Pour les autres: 

 

 

Lien vers le commentaire
Partager sur d’autres sites

Posté (modifié)

Bon j'ai fait le tour ... puisque je vais avoir des rivets ... je vais en mettre un peu

mais je vais mettre aussi des vis et boulons alu M10x1.25

71qPv1R6TCS._AC_SL1000_.jpg

chaque set, en coupant, va me donner 2 vis et 2 boulons M10x1.25 (du M6 il en faudrait une coupe alors qu'avec du M10 - et en y mettant une grosse rondelle de 2"x2" x 1/8ep, je n'en mettrais que 2 par pod et 2 rivets juste pour tenir en place).

https://www.amazon.ca/-/fr/gp/product/B09XHPHSBZ/ref=ox_sc_act_title_2?smid=A22XJM6N54T8XS&psc=1

----

Pour ce qui est du M3 5200, ça coute la peau des fesses - le petit tube payé 46$ taxes in ... chez entrepôt marine

Si ça m'en prend deux, on est à 92$ alors que le PL 295ml me couterait que ( 2x8)16$ taxes in chez réno dépot. Mais dans la vie, un bon sommeil n'a pas de prix 😅 ... et le refaire ... c'est pas plaisant du tout pour son EGO 🤦‍♂️

ET .... Quitte à avoir un pod vide, je l'ai amélioré et va me servir pour mettre des Gillets de sauvetage 🤭

 

Modifié par Bach
  • Like 1
Lien vers le commentaire
Partager sur d’autres sites

Posté (modifié)

J'ai déjà vu des techn installer les pop/blind rivets ... 

J'y crois pas à ça ...

Bien installé sur un établi et avec un outil à air, oui - pas de soucis, la job est nickel chrome.

Mais fait manuellement, et pas de place dégagée ... oufff, j'en ai vu une coupe fait par des sois-disant habitués - c'est à pleurer.

 

---

ajout, j'ai déjà acheté 3 set de M10x1.25 🤨 🤭

Modifié par Bach
ajout
Lien vers le commentaire
Partager sur d’autres sites

Posté (modifié)
Il y a 12 heures, vic130 a dit :

Stainless sur aluminium tu vas finir par avoir de la corosion galvanique. En plus que c'est sous l'eau... Bonjour les trous dans X années!

 

@Bach c'est toi qui vois, tu as quand même un vidéo youtube qui montre que ça marche pareil.

....

 

Pour les autres: 

 

 

J'ai trouvé drôle - quand le gars qui dit que ça prend absolument des rivets en alu ... pis arrive le moment de mettre les rondelles, il n'en trouve pas en alu, alors il y met du stainless - pis il dit ça va bien pareil que les fabricants font ça ... pis pas de soucis 🤨

On aurait voulu avoir une video de son affaire 6 mois après - ca serait plus  rassurant

---

De plus le 3M 5200 vaut 60.14$ sur Amazon.ca - taxes in = 69.16cad - presque 10x le prix du PL premium de Lepage 🤦‍♂️

https://www.amazon.ca/-/fr/51135065204-Marine-Adhésif-mastic-séchage/dp/B000XBFCUO/ref=sr_1_8?__mk_fr_CA=ÅMÅŽÕÑ&crid=311XXFKIJJVTI&keywords=m3+5200&qid=1683975321&sprefix=m3+5200%2Caps%2C83&sr=8-8&ufe=app_do%3Aamzn1.fos.b06bdbbe-20fd-4ebc-88cf-fa04f1ca0da8

Modifié par Bach
modif
Lien vers le commentaire
Partager sur d’autres sites

Il y a 6 heures, Bach a dit :

J'ai trouvé drôle - quand le gars qui dit que ça prend absolument des rivets en alu ... pis arrive le moment de mettre les rondelles, il n'en trouve pas en alu, alors il y met du stainless - pis il dit ça va bien pareil que les fabricants font ça ... pis pas de soucis 🤨

On aurait voulu avoir une video de son affaire 6 mois après - ca serait plus  rassurant

---

De plus le 3M 5200 vaut 60.14$ sur Amazon.ca - taxes in = 69.16cad - presque 10x le prix du PL premium de Lepage 🤦‍♂️

https://www.amazon.ca/-/fr/51135065204-Marine-Adhésif-mastic-séchage/dp/B000XBFCUO/ref=sr_1_8?__mk_fr_CA=ÅMÅŽÕÑ&crid=311XXFKIJJVTI&keywords=m3+5200&qid=1683975321&sprefix=m3+5200%2Caps%2C83&sr=8-8&ufe=app_do%3Aamzn1.fos.b06bdbbe-20fd-4ebc-88cf-fa04f1ca0da8

À défaut d'avoir des washers d'alu, tu peux utiliser un flat bar que tu drilles...

  • Like 1
Lien vers le commentaire
Partager sur d’autres sites

ChatGPT va te le dire. Parce que évidemment l'intelligence artificielle est si avancée...

 

Here are the steps to rivet flotation pods onto an aluminum jon boat:

1. Determine the best placement for the flotation pods on the boat. The pods should be placed symmetrically on either side of the boat to ensure even weight distribution.

2. Clean the area of the boat where the pods will be attached. Use a degreaser and a wire brush to remove any dirt, grease, or oxidation from the aluminum.

3. Drill holes in the pods where the rivets will go. The holes should be slightly smaller than the diameter of the rivets to ensure a tight fit.

4. Place the pods on the boat in the desired location. Make sure they are level and centered before proceeding.

5. Insert the rivets through the holes in the pods and into the corresponding holes in the boat.

6. Use a rivet gun to secure the rivets in place. The gun will deform the end of the rivet, creating a tight seal between the pod and the boat.

7. Repeat this process for each of the rivets, working your way around the pods.

8. Once all of the rivets are in place, check to make sure the pods are securely attached to the boat.

9. Finally, test the boat to ensure that the flotation pods are providing the desired level of buoyancy and stability.

Note: It is important to use the correct size and type of rivets for your particular boat and flotation pods. Consult with a professional or the manufacturer of your boat or pods if you are unsure.

Lien vers le commentaire
Partager sur d’autres sites

il y a 15 minutes, vic130 a dit :

ChatGPT va te le dire. Parce que évidemment l'intelligence artificielle est si avancée...

 

Here are the steps to rivet flotation pods onto an aluminum jon boat:

1. Determine the best placement for the flotation pods on the boat. The pods should be placed symmetrically on either side of the boat to ensure even weight distribution.

2. Clean the area of the boat where the pods will be attached. Use a degreaser and a wire brush to remove any dirt, grease, or oxidation from the aluminum.

3. Drill holes in the pods where the rivets will go. The holes should be slightly smaller than the diameter of the rivets to ensure a tight fit.

4. Place the pods on the boat in the desired location. Make sure they are level and centered before proceeding.

5. Insert the rivets through the holes in the pods and into the corresponding holes in the boat.

6. Use a rivet gun to secure the rivets in place. The gun will deform the end of the rivet, creating a tight seal between the pod and the boat.

7. Repeat this process for each of the rivets, working your way around the pods.

8. Once all of the rivets are in place, check to make sure the pods are securely attached to the boat.

9. Finally, test the boat to ensure that the flotation pods are providing the desired level of buoyancy and stability.

Note: It is important to use the correct size and type of rivets for your particular boat and flotation pods. Consult with a professional or the manufacturer of your boat or pods if you are unsure.

3. Drill holes in the pods where the rivets will go. The holes should be slightly smaller than the diameter of the rivets to ensure a tight fit.

???

---   ---

https://www.fastenermart.com/understanding-blind-rivets.html

Nom.
Rivet Dia.Hole    SizeDrill.               No.

3/32.                  0.097 - 0.100        #41

1/8                     0.129 - 0.133         #30

5/32                  0.160 - 0.164.         #20

3/16                  0.192 - 0.196.          #11

1/4                        0.257 - 0.261.           F           - mon cas

---

Nom. Rivet Dia.   Rivet No.     Rivet Length±0.015 in.     Grip Range (in.)

1/4                            86                    0.580/0.620                        0.251 - 0.375     - mon cas (13mm longueur rivet, grip  

                                                                                                                           0.100+0.100+0.125 fer angle =0.325")

Lien vers le commentaire
Partager sur d’autres sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Invité
Répondre à ce sujet…

×   Vous avez collé du contenu avec mise en forme.   Restaurer la mise en forme

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • En ligne récemment   0 membre est en ligne

    Aucun utilisateur enregistré regarde cette page.




×
×
  • Créer...